Hot and sticky

I downloaded a porn movie.  I checked out what it is and it turned me on.  I hurried up to make a potato starch light.  I checked out the movie some more.  I cut out the best bit with avidemux and looped it.  The starchlight wasn't ready yet.  But anyway I had a go at it.

The hot and sticky starch feels so good.  The problem is that it just flow out when you pump.  But gliding into and out of the warm and sticky mess almost made me cum.  I finally finished with my hand.  But the difference is that the thick warm starch became the lubrication.  It was very good.  It was thick and slippery so you can squeeze hard and jerk hard at the end.  Because the dick is an uneven piece of equipment, you can't please every part without thick lube.  It beats any lub, by sheer volume, temperature.  Of course, don't use it in pussies.

I drilled a hole at the end of the plastic cup to pass the air in use so the thing will not be noisy.  To put water in it I stack it on another cup.  It do not work well with hot water because the uneven distribution of starch will be worsen by trapping something between the two cups.

Add starch to hot water (200F) isn't a good idea after all.  Obviously the starch will be uneven.  You have to stir it well.  This time I used the 1" pipe to stir which is too thick to be good and made a mess.

I never gave up on starch because I knew a warm sticky paste will be good if only for lube.  It's worthwhile to make a harder outer light and use a thinner paste as the lube - and warm.  Looking forward to experimenting next time.

Starch Fleshlight success

Finally, I did it.  I used potato starch, but corn starch will be similar. 

Add starch gradually into hot water, 208F to be exact.  Stir and dissolve.  Add starch until mixture is very thick and do not dissolve starch powder anymore.  The ratio will be between 5:1 to 5:2 by volume of water to starch.

The cup I use is 3 inch diameter, flexible plastic cup from fast food joints.  I put a 1" PVC tube for water in the middle of the cup, for the tunnel for my cock.  Microwave the cup and tube for roughly 30 sec, so that the starch boils over a little bit.  The tube have to be a somewhat smaller than your cock, but not too small.

Wait for the starch to cool down.  You can withdraw the PVC tube by twisting it while pulling.  The starch will glue to the tube but still you can pull it out and leave a tunnel in it.  That can only means success. 

You have to make a small hole at the bottom of the cup to let the air out when you pump.  The starch will block the pump from time to time and became very noise.  You can make a bigger hold and worry about reusing the cup next time.

When you charge fast, there's a lot of resistance.  When you pull out fast, there's a lot of suction, but the starch stays in place, ready for your next charge.  You can do it fast with very pleasant feeling, no hurting.  When ;you move in and out slowly, it's like a blow job.

The best is, you can do it hand free.  Next time I'll see how to mount it on the table top.

No more jelly and grass jelly because they melt.

This is the picture of the fleshlight I made,  AFTER I had sex with it.  You can see my cum in it.  Sorry about that.

Another homemade Fleshlight material comparison

I tried another grass jelly like material called cool fruit.  It is a can like grass jelly, but looked exactly like jello.  This time I used a 3/4" wood drill bit to make a hole in the middle.  The advantage of grass jelly like material can be seen in the drilling.  The drill bit carves into the jelly like wood, making a well defined hole.  I then wobble the drill bit at the top of the whole to make it a little large to custom fit.

The hole makes a lot of difference.  I can insert easily with some force, a bit like inserting into pussy.  The jelly will surround your cock and squeeze it.  The best is you can pull out with very good stimulation.  As you get harder you can exert more force and penetrate deeper into the smaller hole at the bottom of the can.

I had a good climate, with simulated penetration standing up with the can resting on the table edge.  After a lot of abuse, the jelly didn't break, and the hole didn't even get any larger.  Because the hole isn't too small, I can pull out easily with pulling out the jelly from the can.

So far this the best.  I can mount the can on the table top for hand free operation.  You can drain the can a little and most of the residue liquid will be gone.  So there's not much mess but not exactly dry.

I made the full size fleshlight with potato starch.  It was untended but I used the 1:5 mixture of starch and water.  I made it in a plastic cup with 500 ml volume.  I made the hole using the drill but it's like drilling into glue.  The hole is not well defined because the starch clink onto the drill bit.

But anyway I can get in with a stiff cock.  The penetration is OK.  The squeezing sensation  is OK.  But you can really pull out because the starch is clinging onto your cock.  Since you can pull out you can't charge.  When I pull out I pull out the starch from the cup.  It's really like the fleshlight in youtube.  But you can't go up and down because of the stickiness.  But the starch held together OK so I can squeeze my cock with both of my hands.  I can move up and down a bit even the starch is all sticky.

It's a bit of wait for the center of the fleshlight to cool down after in the microwave.  You need to bring the starch and water to boil to activate the starch.  At the moment it's messier than grass jelly because the starch is not evenly cooked.  The top fell off first.  Then more pieces break away when I was exercising;.

Will try the 2:5 mixture to see if I can drill a nice hole in it.